List of ISO standards 5000–7999

This is a list of published International Organization for Standardization (ISO) standards and other deliverables. For a complete and up-to-date list of all the ISO standards, see the ISO catalogue.

The standards are protected by copyright and most of them must be purchased. However, about 300 of the standards produced by ISO and IEC's Joint Technical Committee 1 (JTC 1) have been made freely and publicly available.

ISO 5000 – ISO 7999

ISO 5006:2017 Earth-moving machinery - Operator's field of view - Test method and performance criteria

ISO 5010:2007 Earth-moving machinery - Rubber-tyred machines - Steering requirements

ISO 5011:2014 Inlet air cleaning equipment for internal combustion engines and compressors - Performance testing

ISO 5053 Industrial trucks – Terminology and classification

ISO 5053-1:2015 Part 1: Types of industrial trucks

ISO/IEC 5055:2021 Information technology — Software measurement — Software quality measurement — Automated source code quality measures

ISO 5122:1979 Documentation - Abstract sheets in serial publications

ISO 5123:1984 Documentation - Headers for microfiche of monographs and serials

ISO 5127:2017 Information and documentation - Foundation and vocabulary

ISO 5128:1980 Acoustics – Measurement of noise inside motor vehicles

ISO 5129:2001 Acoustics - Measurement of sound pressure levels in the interior of aircraft during flight

ISO 5130:2007 Acoustics – Measurements of sound pressure level emitted by stationary road vehicles

ISO 5131:2015 Tractors for agriculture and forestry – Measurement of noise at the operator's position – Survey method

ISO 5135:1997 Acoustics – Determination of sound power levels of noise from air-terminal devices, air-terminal units, dampers and valves by measurement in a reverberation room

ISO 5136:2003 Acoustics – Determination of sound power radiated into a duct by fans and other air-moving devices – In-duct method

ISO 5138 Office machines - Vocabulary

ISO 5138-1:1978 Part 1: Dictation equipment

ISO 5138-2:1980 Part 2: Duplicators

ISO 5138-3:1981 Part 3: Addressing machines

ISO 5138-4:1981 Part 4: Letter opening machines

ISO 5138-5:1981 Part 5: Letter folding machines

ISO 5138-7:1986 Part 7: Postal franking machines

ISO 5138-9:1984 Part 9: Typewriters

ISO 5167 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full

ISO 5167-1:2003 Part 1: General principles and requirements

ISO 5167-2:2003 Part 2: Orifice plates

ISO 5167-3:2003 Part 3: Nozzles and Venturi nozzles

ISO 5167-4:2003 Part 4: Venturi tubes

ISO 5167-5:2016 Part 5: Cone meters

ISO 5167-6:2019 Part 6: Wedge meters

ISO 5168:2005 Measurement of fluid flow – Procedures for the evaluation of uncertainties

ISO 5211:2017 Industrial valves - Part-turn actuator attachments

ISO/IEC 5218:2004 Information technology — Codes for the representation of human sexes

ISO/IEC 5230:2020 Information technology — OpenChain Specification

ISO 5232:1998 Graphical symbols for textile machinery

ISO 5234:2005 Textile machinery and accessories – Metallic card clothing – Definitions of dimensions, types and mounting

ISO 5237:1978 Textile machinery and accessories — Cones for yarn winding (cross wound) — Half angle of the cone 5 degrees 57' [Withdrawn: replaced with ISO 8489-5]

ISO 5238 Textile machinery and accessories – Packages of yarns and intermediate products

ISO 5238-1:1982 Part 1: Terminology

ISO 5239:1980 Textile machinery and accessories – Winding – Basic terms

ISO 5247 Textile machinery and accessories – Weaving machines

ISO 5247-1:2004 Part 1: Vocabulary and classification

ISO 5247-3:1993 Part 3: Parts of the machine – Vocabulary

ISO 5248:2003 Textile machinery and accessories – Dyeing and finishing machinery – Vocabulary for ancillary devices

ISO 5250:2003 Textile machinery and accessories – Dyeing and finishing machinery – Terms for tentering and heat-treatment machinery

ISO 5261:1995 Technical drawings – Simplified representation of bars and profile sections

ISO 5284:1986 Conveyor belts – List of equivalent terms

ISO 5288:2001 Synchronous belt drives - Vocabulary

ISO 5323:1984 Solid wood parquet and raw parquet blocks – Vocabulary

ISO 5329:1978 Solid wood paving blocks – Vocabulary

ISO 5344:2004 Electrodynamic vibration generating systems – Performance characteristics

ISO 5347 Methods for the calibration of vibration and shock pick-ups

ISO 5347-8:1993 Part 8: Primary calibration by dual centrifuge

ISO 5347-12:1993 Part 12: Testing of transverse shock sensitivity

ISO 5347-13:1993 Part 13: Testing of base strain sensitivity

ISO 5347-15:1993 Part 15: Testing of acoustic sensitivity

ISO 5347-16:1993 Part 16: Testing of mounting torque sensitivity

ISO 5347-17:1993 Part 17: Testing of fixed temperature sensitivity

ISO 5347-18:1993 Part 18: Testing of transient temperature sensitivity

ISO 5347-22:1997 Part 22: Accelerometer resonance testing – General methods

ISO 5348:1998 Mechanical vibration and shock – Mechanical mounting of accelerometers

ISO 5356 Anaesthetic and respiratory equipment – Conical connectors

ISO 5356-1:2015 Part 1: Cones and sockets

ISO 5356-2:2012 Part 2: Screw-threaded weight-bearing connectors

ISO 5358:1992 Anaesthetic machines for use with humans

ISO 5359:2014 Anaesthetic and respiratory equipment – Low-pressure hose assemblies for use with medical gases

ISO 5360:2016 Anaesthetic vaporizers – Agent-specific filling systems

ISO 5361:2016 Anaesthetic and respiratory equipment – Tracheal tubes and connectors

ISO 5362:2006 Anaesthetic reservoir bags

ISO 5364:2016 Anaesthetic and respiratory equipment – Oropharyngeal airways

ISO 5366:2016 Anaesthetic and respiratory equipment – Tracheostomy tubes and connectors

ISO 5367:2014 Anaesthetic and respiratory equipment – Breathing sets and connectors

ISO 5391:2003 Pneumatic tools and machines - Vocabulary

ISO 5396:1977 Hardmetal heading dies - Terminology

ISO 5408:2009 Screw threads - Vocabulary

ISO 5419:1982 Twist drills - Terms, definitions and types

ISO 5420:1983 Reamers - Terms, definitions and types

ISO 5426:1983 Information and documentation - Extension of the Latin alphabet coded character set for bibliographic information interchange

ISO 5426-2:1996 Part 2: Latin characters used in minor European languages and obsolete typography

ISO 5427:1984 Extension of the Cyrillic alphabet coded character set for bibliographic information interchange

ISO 5428:1984 Greek alphabet coded character set for bibliographic information interchange

ISO 5436 Geometrical Product Specifications (GPS) – Surface texture: Profile method; Measurement standards

ISO 5436-1:2000 Part 1: Material measures

ISO 5436-2:2012 Part 2: Software measurement standards

ISO 5445:1980 Ferrosilicon - Specification and conditions of delivery

ISO 5446:2017 Ferromanganese - Specification and conditions of delivery

ISO 5447:1980 Ferrosilicomanganese - Specification and conditions of delivery

ISO 5448:1981 Ferrochromium - Specification and conditions of delivery

ISO 5449:1980 Ferrosilicochromium - Specification and conditions of delivery

ISO 5450:1980 Ferrotungsten - Specification and conditions of delivery

ISO 5451:1980 Ferrovanadium - Specification and conditions of delivery

ISO 5452:1980 Ferromolybdenum - Specification and conditions of delivery

ISO 5453:1980 Ferroniobium - Specification and conditions of delivery

ISO 5454:1980 Ferrotitanium - Specification and conditions of delivery

ISO 5455:1979 Technical drawings – Scales

ISO 5456 Technical drawings – Projection methods

ISO 5456-1:1996 Part 1: Synopsis

ISO 5456-2:1996 Part 2: Orthographic representations

ISO 5456-3:1996 Part 3: Axonometric representations

ISO 5456-4:1996 Part 4: Central projection

ISO 5457:1999 Technical product documentation – Sizes and layout of drawing sheets

ISO 5458:1998 Geometrical Product Specifications (GPS) – Geometrical tolerancing – Positional tolerancing

ISO 5459:2011 Geometrical product specifications (GPS) – Geometrical tolerancing – Datums and datum systems

ISO 5479:1997 Statistical interpretation of data - Tests for departure from the normal distribution

ISO 5492:2008 Sensory analysis – Vocabulary

ISO 5496:2006 Sensory analysis – Methodology – Initiation and training of assessors in the detection and recognition of odours

ISO 5507:2002 Oilseeds, vegetable oils and fats – Nomenclature

ISO 5526:2013 Cereals, pulses and other food grains – Nomenclature

ISO 5527:2015 Cereals – Vocabulary

ISO 5572:1987 Shipbuilding and marine structures - Numbering of equipment and structural elements in ships

ISO 5576:1997 Non-destructive testing - Industrial X-ray and gamma-ray radiology - Vocabulary

ISO 5577:2017 Non-destructive testing - Ultrasonic testing - Vocabulary

ISO 5593:1997 Rolling bearings - Vocabulary

ISO 5598:2008 Fluid power systems and components - Vocabulary

ISO 5652:1984 Information processing – 9-Track, 12,7 mm (0.5 in) wide magnetic tape for information interchange – Format and recording, using group coding at 246 cpmm (6 250 cpi)

ISO 5653:1980 Information processing – Interchangeable magnetic twelve-disk pack (200 Mbytes)

ISO 5654 Information processing – Data interchange on 200 mm (8 in) flexible disk cartridges using two-frequency recording at 13 262 ftprad, 1,9 tpmm (48 tpi), on one side

ISO 5654-1:1984 Part 1: Dimensional, physical and magnetic characteristics

ISO 5654-2:1985 Part 2: Track format

ISO 5659 Plastics - Smoke generation

ISO 5659-1:1996 Part 1: Guidance on optical-density testing [Withdrawn: replaced by ISO 5659-2:2012]

ISO 5659-2:2017 Part 2: Determination of optical density by a single-chamber test

ISO/TR 5659-3:1999 Part 3: Determination of optical density by a dynamic-flow method [Withdrawn, no replacement]

ISO 5660 Reaction-to-fire tests – Heat release, smoke production and mass loss rate

ISO 5660-1 Heat release rate (cone calorimeter method)

ISO 5660-2 Smoke production rate (dynamic measurement)

ISO/TS 5660-3 Guidance on measurement

ISO 5681:1992 Equipment for crop protection – Vocabulary

ISO 5702:1983 Equipment for harvesting – Combine harvester component parts – Equivalent terms

ISO 5725 Accuracy (trueness and precision) of measurement methods and results

ISO 5725-1:1994 Part 1: General principles and definitions

ISO 5725-2:1994 Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method

ISO 5725-3:1994 Part 3: Intermediate measures of the precision of a standard measurement method

ISO 5725-4:1994 Part 4: Basic methods for the determination of the trueness of a standard measurement method

ISO 5725-5:1998 Part 5: Alternative methods for the determination of the precision of a standard measurement method

ISO 5725-6:1994 Part 6: Use in practice of accuracy values

ISO 5742:2004 Pliers and nippers - Nomenclature

ISO 5775 Bicycle tires and rims

ISO 5776 Graphic technology - Symbols for text correction

ISO 5800:2001 Photography – Colour negative films for still photography – Determination of ISO speed

ISO 5806:1984 Information processing - Specification of single-hit decision tables

ISO 5807:1985 Information processing - Documentation symbols and conventions for data, program and system flowcharts, program network charts and system resources charts

ISO 5826:2014 Resistance welding equipment – Transformers – General specifications applicable to all transformers

ISO 5832 Implants for surgery – Metallic materials

ISO 5832-1:2016 Part 1: Wrought stainless steel

ISO 5832-2:1999 Part 2: Unalloyed titanium

ISO 5832-3:2016 Part 3: Wrought titanium 6-aluminium 4-vanadium alloy

ISO 5832-4:2014 Part 4: Cobalt-chromium-molybdenum casting alloy

ISO 5832-5:2005 Part 5: Wrought cobalt-chromium-tungsten-nickel alloy

ISO 5832-6:1997 Part 6: Wrought cobalt-nickel-chromium-molybdenum alloy

ISO 5832-7:2016 Part 7: Forgeable and cold-formed cobalt-chromium-nickel-molybdenum-iron alloy

ISO 5832-8:1997 Part 8: Wrought cobalt-nickel-chromium-molybdenum- tungsten-iron alloy

ISO 5832-9:2007 Part 9: Wrought high nitrogen stainless steel

ISO 5832-11:2014 Part 11: Wrought titanium 6-aluminium 7-niobium alloy

ISO 5832-12:2007 Part 12: Wrought cobalt-chromium-molybdenum alloy

ISO 5832-14:2007 Part 14: Wrought titanium 15-molybdenum 5-zirconium 3-aluminium alloy

ISO 5833:2002 Implants for surgery – Acrylic resin cements

ISO 5834 Implants for surgery – Ultra-high-molecular-weight polyethylene

ISO 5834-1:2005 Part 1: Powder form

ISO 5834-2:2011 Part 2: Moulded forms

ISO 5834-3:2005 Part 3: Accelerated ageing methods

ISO 5834-4:2005 Part 4: Oxidation index measurement method

ISO 5834-5:2005 Part 5: Morphology assessment method

ISO 5835:1991 Implants for surgery – Metal bone screws with hexagonal drive connection, spherical under-surface of head, asymmetrical thread – Dimensions

ISO 5836:1988 Implants for surgery – Metal bone plates – Holes corresponding to screws with asymmetrical thread and spherical under-surface

ISO 5837 Implants for surgery – Intramedullary nailing systems

ISO 5837-1:1985 Part 1: Intramedullary nails with cloverleaf or V-shaped cross-section

ISO 5838 Implants for surgery – Metallic skeletal pins and wires

ISO 5838-1:2013 Part 1: General requirements

ISO 5838-2:1991 Part 2: Steinmann skeletal pins – Dimensions

ISO 5838-3:1993 Part 3: Kirschner skeletal wires

ISO 5840 Cardiovascular implants – Cardiac valve prostheses

ISO 5840-1:2015 Part 1: General requirements

ISO 5840-2:2015 Part 2: Surgically implanted heart valve substitutes

ISO 5840-3:2013 Part 3: Heart valve substitutes implanted by transcatheter techniques

ISO 5841 Implants for surgery – Cardiac pacemakers

ISO 5841-2:2014 Part 2: Reporting of clinical performance of populations of pulse generators or leads

ISO 5841-3:2013 Part 3: Low-profile connectors (IS-1) for implantable pacemakers

ISO 5843 Aerospace - List of equivalent terms

ISO 5843-1:1985 Part 1: Aerospace electrical equipment

ISO 5843-2:1990 Part 2: Aerospace rivets

ISO 5843-3:1997 Part 3: Aerospace bolts and nuts

ISO 5843-4:1990 Part 4: Flight dynamics

ISO 5843-5:1990 Part 5: Environmental and operating conditions for aircraft equipment

ISO 5843-6:1985 Part 6: Standard atmosphere

ISO 5843-8:1988 Part 8: Aircraft reliability

ISO 5843-9:1988 Part 9: Aircraft

ISO 5843-10:1988 Part 10: Aircraft structure

ISO 5845 Technical drawings – Simplified representation of the assembly of parts with fasteners

ISO 5845-1:1995 Part 1: General principles

ISO 5845-2:1995 Part 2: Rivets for aerospace equipment

ISO 5859:2014 Aerospace series - Graphic symbols for schematic drawings of hydraulic and pneumatic systems and components

ISO 5878:1982 Reference atmospheres for aerospace use

ISO 5893 Rubber and plastics test equipment – Tensile, flexural and compression types (constant rate of traverse) – Specification

ISO 5963:1985 Documentation - Methods for examining documents, determining their subjects, and selecting indexing terms

ISO 5964 Documentation – Guidelines for the establishment and development of multilingual thesauri

ISO 5967:1981 Taps and thread cutting - Nomenclature of the main types and terminology

ISO 5968:1981 Circular screwing dies - Terminology

ISO 5971:1981 Size designation of clothes – Pantyhose

ISO 5989:1995 Photography - Pre-packaged chemicals for the processing of silver halide based photographic materials - Vocabulary

ISO 5993 Sodium hydroxide for industrial use—Determination of mercury content—Flameless atomic absorption spectrometric method

ISO 6009:2016 Hypodermic needles for single use – Colour coding for identification

ISO 6011:2003 Earth-moving machinery – Visual display of machine operation

ISO 6050:1987 Shipbuilding - Bulbous bow and side thruster symbols

ISO 6068:1985 Information processing – Recording characteristics of instrumentation magnetic tape (including telemetry systems) – Interchange requirements

ISO 6070:1981 Auxiliary tables for vibration generators – Methods of describing equipment characteristics

ISO 6078:1982 Black tea – Vocabulary

ISO 6093:1985 Information processing - Representation of numerical values in character strings for information interchange

ISO 6098:1984 Information processing – Self-loading cartridges for 12,7 mm (0.5 in) wide magnetic tape

ISO 6107 Water quality—Vocabulary

ISO 6107-1:2004 (No part title)

ISO 6107-2:2006 (No part title)

ISO 6107-3:1993 (No part title)

ISO 6107-4:1993 (No part title)

ISO 6107-5:2004 (No part title)

ISO 6107-6:2004 (No part title)

ISO 6107-7:2006 (No part title)

ISO 6107-8:1993 (No part title)

ISO 6107-9:1997 Part 9: Alphabetical list and subject index

ISO 6152:1982 Thermometers for use with alcoholometers and alcohol hydrometers

ISO 6160:1979 Programming languages - PL/1

ISO 6165:2012 Earth-moving machinery – Basic types – Identification and terms and definitions

ISO 6166:2013 Securities and related financial instruments – International securities identification numbering system (ISIN)

ISO 6173:1982 Open-end spinning machines – Vocabulary

ISO 6188:1986 Plastics — Poly(alkylene terephthalate) granules — Determination of water content [Withdrawn: replaced with ISO 15512]

ISO 6194 Rotary-shaft lip-type seals incorporating elastomeric sealing elements

ISO 6194-2:2009 Part 2: Vocabulary

ISO 6194-5 Identification of visual imperfections

ISO 6196 Micrographics - Vocabulary

ISO 6196-1:1993 Part 1: General terms

ISO 6196-2:1993 Part 2: Image positions and methods of recording

ISO 6196-3:1997 Part 3: Film processing

ISO 6196-4:1998 Part 4: Materials and packaging

ISO 6196-5:1987 Part 5: Quality of images, legibility, inspection

ISO 6196-6:1992 Part 6: Equipment

ISO 6196-7:1992 Part 7: Computer micrographics

ISO 6196-8:1998 Part 8: Use

ISO 6196-10:1999 Part 10: Index

ISO 6206:1979 Chemical products for industrial use – Sampling – Vocabulary

ISO 6217:1982 Shipbuilding – Inland navigation – Pilot craft – Identification painting and inscriptions

ISO 6222:1999 Water quality – Enumeration of culturable micro-organisms – Colony count by inoculation in a nutrient agar culture medium

ISO 6284:1996 Construction drawings – Indication of limit deviations

ISO 6289:2003 Skis – Vocabulary

ISO 6336 Calculation of load capacity of spur and helical gears

ISO 6344 Coated abrasives – Grain size analysis

ISO 6345:1990 Shipbuilding and marine structures – Windows and side scuttles – Vocabulary

ISO 6346 Freight containers – Coding, identification and marking

ISO 6348:1980 Textiles – Determination of mass – Vocabulary

ISO 6352:1985 Ferronickel - Determination of nickel content - Dimethylglyoxime gravimetric method

ISO 6354:1982 Adhesives – Vocabulary [Withdrawn: replaced with ISO 472]

ISO 6355:1988 Textile glass – Vocabulary [Withdrawn: replaced with ISO 472]

ISO 6357:1985 Documentation – Spine titles on books and other publications

ISO 6372:2017 Nickel and nickel alloys – Terms and definitions

ISO 6385:2016 Ergonomics principles in the design of work systems

ISO 6393:2008 Earth-moving machinery – Determination of sound power level – Stationary test conditions

ISO 6394:2008 Earth-moving machinery – Determination of emission sound pressure level at operator's position – Stationary test conditions

ISO 6395:2008 Earth-moving machinery – Determination of sound power level – Dynamic test conditions

ISO 6396:2008 Earth-moving machinery – Determination of emission sound pressure level at operator's position – Dynamic test conditions

ISO 6405 Earth-moving machinery - Symbols for operator controls and other displays

ISO 6405-1:2017 Part 1: Common symbols

ISO 6405-2:2017 Part 2: Symbols for specific machines, equipment and accessories

ISO 6410 Technical drawings – Screw threads and threaded parts

ISO 6410-1:1993 Part 1: General conventions

ISO 6410-2:1993 Part 2: Screw thread inserts

ISO 6410-3:1993 Part 3: Simplified representation

ISO 6411:1982 Technical drawings – Simplified representation of centre holes

ISO 6412 Technical drawings – Simplified representation of pipelines

ISO 6412-1:2017 Part 1: General rules and orthogonal representation

ISO 6412-2:2017 Part 2: Isometric projection

ISO 6412-3:2017 Part 3: Terminal features of ventilation and drainage systems

ISO 6413:1988 Technical drawings – Representation of splines and serrations

ISO 6414:1982 Technical drawings for glassware

ISO 6416:2017 Hydrometry – Measurement of discharge by the ultrasonic transit time (time of flight) method

ISO 6420:2016 Hydrometry – Position fixing equipment for hydrometric boats

ISO 6421:2012 Hydrometry – Methods for assessment of reservoir sedimentation

ISO 6422 Layout key for trade documents

ISO 6422-1:2010 Part 1: Paper-based documents

ISO 6425:1996 Divers' watches

ISO 6426 Horological vocabulary

ISO 6426-1:1982 Part 1: Technical and scientific definitions

ISO 6426-2:2002 Part 2: Technical and commercial definitions

ISO 6428:1982 Technical drawings – Requirements for microcopying

ISO/IEC 6429:1992 Information technology – Control functions for coded character sets

ISO 6433:2012 Technical product documentation – Part references

ISO 6438:1983 Documentation – African coded character set for bibliographic information interchange

ISO 6461 Water quality – Detection and enumeration of the spores of sulfite-reducing anaerobes (clostridia)

ISO 6461-1:1986 Part 1: Method by enrichment in a liquid medium

ISO 6461-2:1986 Part 2: Method by membrane filtration

ISO 6467:1980 Ferrovanadium - Determination of vanadium content - Potentiometric method

ISO 6472:2017 Rubber compounding ingredients – Abbreviated terms

ISO 6474 Implants for surgery – Ceramic materials

ISO 6474-1:2010 Part 1: Ceramic materials based on high purity alumina

ISO 6474-2:2012 Part 2: Composite materials based on a high-purity alumina matrix with zirconia reinforcement

ISO 6475:1989 Implants for surgery – Metal bone screws with asymmetrical thread and spherical under-surface – Mechanical requirements and test methods

ISO 6501:1988 Ferronickel - Specification and delivery requirements

ISO 6512:1982 Building construction — Modular coordination — Storey heights and room heights [Withdrawn: replaced with ISO 21723]

ISO 6513:1982 Building construction — Modular coordination — Series of preferred multimodular sizes for horizontal dimensions [Withdrawn: replaced with ISO 21723]

ISO 6514:1982 Building construction — Modular coordination — Sub-modular increments [Withdrawn: replaced with ISO 21723]

ISO 6518 Road vehicles – Ignition systems

ISO 6518-1:2002 Part 1: Vocabulary

ISO/IEC 6522:1992 Information technology - Programming languages - PL/1 general purpose subset

ISO/IEC 6523 Information technology – Structure for the identification of organizations and organization parts

ISO 6531:2017 Machinery for forestry – Portable chain-saws – Vocabulary

ISO 6552:1980 Automatic steam traps - Definition of technical terms

ISO 6579 Microbiology of the food chain – Horizontal method for the detection, enumeration and serotyping of Salmonella

ISO 6579-1:2017 Part 1: Detection of Salmonella spp.

ISO/TS 6579-2:2012 Part 2: Enumeration by a miniaturized most probable number technique

ISO/TR 6579-3:2014 Part 3: Guidelines for serotyping of Salmonella spp.

ISO 6586:1980 Data processing - Implementation of the ISO 7- bit and 8- bit coded character sets on punched cards

ISO 6590 Packaging – Sacks – Vocabulary and types

ISO 6590-1:1983 Part 1: Paper sacks

ISO 6590-2:1986 Part 2: Sacks made from thermoplastic flexible film

ISO 6594 Cast iron drainage pipes and fittings – Spigot series

ISO 6596 Information processing – Data interchange on 130 mm (5.25 in) flexible disk cartridges using two-frequency recording at 7 958 ftprad, 1.9 tpmm (48 tpi), on one side

ISO 6596-1:1985 Part 1: Dimensional, physical and magnetic characteristics

ISO 6596-2:1985 Part 2: Track format

ISO 6611:2004 Milk and milk products – Enumeration of colony-forming units of yeasts and/or moulds – Colony-count technique at 25 degrees C

ISO 6621 Internal combustion engines – Piston rings

ISO 6621-1:2007 Part 1: Vocabulary

ISO 6630:1986 Documentation - Bibliographic control characters

ISO 6689 Equipment for harvesting – Combines and functional components

ISO 6689-1:1997 Part 1: Vocabulary

ISO 6706:1981 Plastics laboratory ware – Graduated measuring cylinders

ISO 6707 Buildings and civil engineering works – Vocabulary

ISO 6707-1:2014 Part 1: General terms

ISO 6707-2:2014 Part 2: Contract terms

ISO 6707-3:2017 Part 3: Sustainability terms

ISO 6709:2008 Standard representation of geographic point location by coordinates

ISO 6710:2017 Single-use containers for human venous blood specimen collection

ISO 6725:1981 Road vehicles – Dimensions of two-wheeled mopeds and motorcycles – Terms and definitions

ISO 6726:1988 Mopeds and motorcycles with two wheels – Masses – Vocabulary

ISO 6727:2012 Road vehicles - Motorcycles - Symbols for controls, indicators and tell-tales

ISO 6730:2005 Milk – Enumeration of colony-forming units of psychrotrophic microorganisms – Colony-count technique at 6,5 degrees C

ISO 6747:2013 Earth-moving machinery – Dozers – Terminology and commercial specifications

ISO 6780:2003 Flat pallets for intercontinental materials handling — Principal dimensions and tolerances, reviewed and confirmed 2014

ISO 6798:1995 Reciprocating internal combustion engines – Measurement of emitted airborne noise – Engineering method and survey method

ISO 6811:1998 Spherical plain bearings - Vocabulary

ISO 6813:1998 Road vehicles – Collision classification – Terminology

ISO 6814:2009 Machinery for forestry – Mobile and self-propelled machinery – Terms, definitions and classification

ISO 6861:1996 Information and documentation - Glagolitic alphabet coded character set for bibliographic information interchange

ISO 6862:1996 Information and documentation - Mathematical coded character set for bibliographic information interchange

ISO 6871 Dental base metal casting alloys

ISO 6871-1:1994 Part 1: Cobalt-based alloys [Withdrawn: replaced with ISO 22674]

ISO 6871-2:1994 Part 2: Nickel-based alloys [Withdrawn: replaced with ISO 22674]

ISO 6883:2017 Animal and vegetable fats and oils - Determination of conventional mass per volume (litre weight in air)

ISO 6887 Microbiology of the food chain - Preparation of test samples, initial suspension and decimal dilutions for microbiological examination

ISO 6887-1:2017 Part 1: General rules for the preparation of the initial suspension and decimal dilutions

ISO 6887-2:2017 Part 2: Specific rules for the preparation of meat and meat products

ISO 6887-3:2017 Part 3: Specific rules for the preparation of fish and fishery products

ISO 6887-4:2017 Part 4: Specific rules for the preparation of miscellaneous products

ISO 6887-5:2010 Part 5: Specific rules for the preparation of milk and milk products

ISO 6887-6:2013 Part 6: Specific rules for the preparation of samples taken at the primary production stage

ISO 6888 Microbiology of food and animal feeding stuffs – Horizontal method for the enumeration of coagulase-positive staphylococci (Staphylococcus aureus and other species)

ISO 6888-1:1999 Part 1: Technique using Baird-Parker agar medium

ISO 6888-2:1999 Part 2: Technique using rabbit plasma fibrinogen agar medium

ISO 6888-3:2003 Part 3: Detection and MPN technique for low numbers

ISO 6892 Metallic materials – Tensile testing

ISO 6892-1 Method of test at room temperature

ISO 6892-2 Method of test at elevated temperature

ISO 6892-3 Method of test at low temperature

ISO 6892-4 Method of test in liquid helium

ISO 6926:2016 Acoustics – Requirements for the performance and calibration of reference sound sources used for the determination of sound power levels

ISO 6927:2012 Buildings and civil engineering works – Sealants – Vocabulary

ISO 6929:2013 Steel products – Vocabulary

ISO 6936:1988 Information processing - Conversion between the two coded character sets of ISO 646 and ISO 6937-2 and the CCITT international telegraph alphabet No.